Configuração da USB para programação do FPGA via JTAG
LINUX
Antes de poder programar um FPGA usando a interface JTAG é necessário Configurar a USB Blaster para a programação JTAG.
O procedimento abaixo é usado nos kits:
- DE2-115, DE0-Nano, DE0 da Altera
- Mercurio IV da Macnica
Executar como root os seguintes comandos para criar o arquivo altera-usb-blaster.rules na pasta /etc/udev/rules.d
gedit /etc/udev/rules.d/altera-usb-blaster.rules
Com o conteúdo:
ATTR{idVendor}=="09fb", ATTR{idProduct}=="6001", MODE="666" ATTR{idVendor}=="09fb", ATTR{idProduct}=="6002", MODE="666" ATTR{idVendor}=="09fb", ATTR{idProduct}=="6003", MODE="666" ATTR{idVendor}=="09fb", ATTR{idProduct}=="6010", MODE="666" ATTR{idVendor}=="09fb", ATTR{idProduct}=="6810", MODE="666"
Reinicie o computador.
Para verificar se a JTAG está configurada corretamente, conecte a placa usando a USB e ligue-a.
/opt/altera/intelFPGA/20.1/quartus/bin/jtagconfig
ou
/opt/intelFPGA/20.1/quartus/bin/jtagconfig
Se estiver OK, deve aparece alguma mensagem do tipo:
1) USB-Blaster [N-N] 020F40DD 10CL040(Y|Z)/EP3C40/EP4CE30/..
Se permanecer a mensagem abaixo, desligue o kit, ou retire o cabo USB, e reconecte ou ligue novamente o kit.
1) USB-Blaster variant [N-N] Unable to lock chain (Insufficient port permissions)
Caso não esteja OK, aparecerá:
No JTAG hardware available
FONTE: http://www.altera.com/download/drivers/dri-usb_b-lnx.html FONTE: http://www.eecg.toronto.edu/~laforest/USB-Blaster-Debian.html
- Problema 2
Caso o procedimento acima tenha sido feito e mesmo assim ao executar o comando
jtagconfig
Não houver uma resposta com os dados da interface utilizada (020F40DD 10CL040(Y|Z)/EP3C40/EP4CE30/..), e o terminar ficar travado com a linha
1) USB-Blaster [N-N]
Será necessário um outro método para acessar a JTAG. A solução encontrada é "matar" o serviço jtagd e reiniciá-lo.
pkill -f jtagd -9; /opt/altera/intelFPGA/20.1/quartus/bin/jtagd --user-start; /opt/altera/intelFPGA/20.1/quartus/bin/jtagconfig
ou
pkill -f jtagd -9; /opt/intelFPGA/20.1/quartus/bin/jtagd --user-start; /opt/intelFPGA/20.1/quartus/bin/jtagconfig
Se tudo estiver correto o terminal deverá mostrar:
1) USB-Blaster [N-N] 020F40DD 10CL040(Y|Z)/EP3C40/EP4CE30/..
WINDOWS
Quando alguém precisar, escrever o procedimento.
Installing Altera usb Blaster Driver
- Plug in the power and turn on your development board
- Plug in your Development board or USB Blaster device into a free USB port
- In Windows 7, 8, 8.1, and 10 go to Start and search for “device manager”
- Click on Device manager in the search results
- In device manager find the item list “other devices”
- Expand that list and there should be “Altera USB-Blaster”
- Right click on Altera USB-Blaster
- Choose Update Driver Software...
- In the popup choose “Browse my computer for driver software”
- Click Browse and navigate to the altera folder C:\altera
- Make sure the “Include Subfolders” is checked
- Click next
- If successful windows will say “Windows has successfully updated your driver software” Click close
- Back in device manager under Universal Serial Bus Controllers there should be the Altera USB-Blaster
- Close out of Device manager and you are now ready to program your Development board.
- Note: On the DE2-115 there are two USB ports but the one closet to the edge is the USB blaster
- Note: It is best to NOT use USB ports that have active power or an “always on” feature as these ports can damage your development board or USB blaster chip
FONTE: http://fpga.seanwrall.com/lessons/lesson4/ e pdf, video