Telecom20162 pji3 configuracoes
Link curto: http://bit.ly/2cMDeey
Operadora
> Arquivo de configuração das interfaces de redes /etc/network/interfaces
# interfaces(5) file used by ifup(8) and ifdown(8)
auto lo
iface lo inet loopback
- Onboard interface
auto eth0
iface eth0 inet manual
bond-master bond0
bond-use-carrier 1
- Offboard interface
auto eth1
iface eth1 inet manual
bond-master bond0
bond-use-carrier 1
- Bonding
auto bond0
iface bond0 inet manual
bond-slaves none
bond-lacp-rate fast
bond-mode 802.3ad
bond-xmit_hash_policy layer2+3
bond-miimon 100
auto bond0.10
iface bond0.10 inet static
address 192.168.10.10
netmask 255.255.255.0
auto bond0.20
iface bond0.20 inet static
address 192.168.20.10
netmask 255.255.255.0
auto bond0.30
iface bond0.30 inet static
address 200.135.37.125
netmask 255.255.255.192
gateway 200.135.37.126
dns-nameservers 8.8.8.8 8.8.4.4
auto bond0.40
iface bond0.40 inet static
address 192.168.40.10
netmask 255.255.255.0
</syntaxhighlight>
> Arquivo script de inicialização
/etc/rc.local
- !/bin/sh -e
- rc.local
- This script is executed at the end of each multiuser runlevel.
- Make sure that the script will "exit 0" on success or any other
- value on error.
- In order to enable or disable this script just change the execution
- bits.
- By default this script does nothing.
killall pppoe-server # Mata qualquer processo pppoe rodando
pppoe-server -C pji -L 10.0.0.1 -p /etc/ppp/faixa-ip -I bond0.40 # Cria um novo processo pppoe
sysctl -w net.ipv4.conf.all.forwarding=1 # Habilita o roteamento no servidor
iptables -t nat -A POSTROUTING -o bond0.30 -j MASQUERADE # Configura o NAT
exit 0
</syntaxhighlight>
> VLANS no Switch da Operadora
Switch2#show vlan
VLAN Name Status Ports
-------------------------------- --------- -------------------------------
1 default active Gi1/0/25, Gi1/0/26, Gi1/0/27
Gi1/0/28
10 VLAN0010 active Gi1/0/3, Gi1/0/4, Gi1/0/5
Gi1/0/6, Gi1/0/7, Gi1/0/8
Gi1/0/9, Gi1/0/10, Gi1/0/11
Gi1/0/12
20 VLAN0020 active Gi1/0/13, Gi1/0/14, Gi1/0/15
Gi1/0/16, Gi1/0/17, Gi1/0/18
Gi1/0/19, Gi1/0/20, Gi1/0/21
Gi1/0/22
30 VLAN0030 active Gi1/0/2
40 VLAN0040 active Gi1/0/1
</syntaxhighlight>
> Interface PO 1 do Switch da Operadora
Switch2#show running-config interface port-channel 1
Building configuration...
Current configuration : 97 bytes
!
interface Port-channel1
switchport trunk allowed vlan 10,20,30,40
switchport mode trunk
end
</syntaxhighlight>
> Resumo das interfaces do Switch da Operadora
Switch2#show running-config interface gigabitEthernet 1/0/1
Building configuration...
Current configuration : 89 bytes
!
interface GigabitEthernet1/0/1
switchport access vlan 40
switchport mode access
end
Switch2#show running-config interface gigabitEthernet 1/0/2
Building configuration...
Current configuration : 89 bytes
!
interface GigabitEthernet1/0/2
switchport access vlan 30
switchport mode access
end
Switch2#show running-config interface gigabitEthernet 1/0/23
Building configuration...
Current configuration : 134 bytes
!
interface GigabitEthernet1/0/23
switchport trunk allowed vlan 10,20,30,40
switchport mode trunk
channel-group 1 mode active
end
Switch2#show running-config interface gigabitEthernet 1/0/24
Building configuration...
Current configuration : 134 bytes
!
interface GigabitEthernet1/0/24
switchport trunk allowed vlan 10,20,30,40
switchport mode trunk
channel-group 1 mode active
end
</syntaxhighlight>
> Interfaces de uso geral do Switch da Operadora
As interfaces de 1/0/3 a 1/0/12 estão na VLAN 10 no modo access
As interfaces de 1/0/13 a 1/0/22 estão na VLAN 20 no modo access
interface GigabitEthernet1/0/12
switchport access vlan 10
switchport mode access
!
interface GigabitEthernet1/0/13
switchport access vlan 20
switchport mode access
</syntaxhighlight>