Usuário:RonaldoLages
Revisão de 17h08min de 25 de novembro de 2010 por Rclages (discussão | contribs) (→Configuração do Servidor de Desenvolvimento)
IF-SC Palhoça Bilíngue
Configuração do Servidor de Desenvolvimento
BIOS
- Ligar o servidor
- Pressionar botão preto acima da logomarca DELL (instalado na posição vertical)
- Teclar F12 durante a inicialização do hardware
- Aparece mensagem F12 Boot Options no canto superior direito da tela
- Mensagem muda para Preparing one-time boot menu... em verde
- Tela Boot Device Menu é mostrada
- 1ª opção ( ) vem selecionada
- Mudar para 4ª opção: System Setup
- Teclar <ENTER>
- Tela gráfica Dell Inc. OptiPlex 780 mostrada (acompanhar menu à esquerda):
- Settings (1º nível)
- General (2º nível)
- System Board (3º nível)
- Nada a fazer, apenas informações para conhecimento
- Date/Time (3º nível)
- Atualizar data e hora mudando os valores necessários (AM = antes meio-dia, PM = após meio-dia)
- Boot Sequence (3º nível)
- Conferir marcação (coluna esquerda) e ordem (coluna direita) dos dispositivos
- System Board (3º nível)
- Drives (2º nível)
- Diskette Drive (3º nível)
- Conferir marcação pois dispositivo de disquete não será usado
- SATA Operation (3º nível)
- Conferir marcação pois dispositivo de disquete não será usado
- SMART Operation (3º nível)
- Conferir marcação pois usaremos SMART para monitorar o HD
- Drives (3º nível)
- Conferir marcação pois usaremos somente interfaces SATA-0 (HD) e SATA-1 (DVD)
- Diskette Drive (3º nível)
- System Configuration (2º nível)
- Integrated NIC (3º nível)
- Conferir marcação pois usaremos NIC sem PXE ou ImageServer
- USB Controller (3º nível)
- Conferir marcação pois dispositivos USB serão permitidos
- Parallel Port (3º nível)
- Conferir marcação pois interface paralela não será usada
- Parallel Port Address (3º nível)
- Como não teremos interface paralela, então este opção não pode ser alterada
- Serial Port #1 (3º nível)
- Como não teremos interface serial, então este opção não pode ser alterada
- Miscellaneous Devices (3º nível)
- Conferir marcação pois termos USB Quad e Dual, além de PCI e Audio
- Integrated NIC (3º nível)
- Video (2º nível)
- Primary Video (3º nível)
- Conferir marcação pois teremos placa gráfica PCI Express neste servidor
- Primary Video (3º nível)
- Performance (2º nível)
- Multi Core Support (3º nível)
- Conferir marcação pois usaremos CPU multi core
- Intel(R) SpeedStep(TM) (3º nível)
- Conferir marcação pois usaremos esta facilidade da Intel(R)
- C States Control (3º nível)
- Conferir marcação pois não usaremos esta função do processador
- Limit CPUID Value (3º nível)
- Conferir marcação pois não usaremos esta limitação do processador
- Multi Core Support (3º nível)
- Virtualization Support (2º nível)
- Virtualization (3º nível)
- Conferir marcação pois usaremos esta facilidade na virtualização
- VT for Direct I/O (3º nível)
- Conferir marcação pois usaremos esta facilidade na virtualização
- Virtualization (3º nível)
- Security (2º nível)
- Administrator Password (3º nível)
- Digitar password mestre conforme frase "Gott ist ein Popstar"
- System Password (3º nível)
- Não digitar password pois não usaremos este nível de proteção da BIOS
- Password Changes (3º nível)
- Conferir marcação pois usaremos este nível de proteção da BIOS
- TPM Security (3º nível)
- Facilidade não habilitada portanto não pode ser alterada
- CPU XD Support (3º nível)
- Conferir marcação pois usaremos este recurso de segurança
- Computrace(R) (3º nível)
- Conferir marcação pois não usaremos este recurso de segurança
- Chassis Intrusion (3º nível)
- Conferir marcação pois usaremos este recurso de segurança
- SATA-0 Password (3º nível)
- Não digitar password pois não usaremos este nível de proteção da BIOS
- Administrator Password (3º nível)
- Power Management
- AC Recovery
- Conferir marcação pois usaremos este recurso de gerenciamento de energia
- Auto On Time
- Conferir marcação pois não usaremos ligamento automático
- Low Power Mode
- Conferir marcação pois usaremos este recurso de gerenciamento de energia
- Remote Wake Up
- Conferir marcação pois usaremos este recurso de ligamento remoto
- Suspend Mode
- Conferir marcação pois usaremos este recurso de economia de energia
- Fan Control Override
- Conferir marcação pois não usaremos este controle de ventilador
- AC Recovery
- General (2º nível)
- Settings (1º nível)
- Mudar para item Maintenance (2º nível)
- Mudar para item Service Tag (3º nível)
- Conferir valor indicado mas não alterá-lo
- Mudar para item Service Tag (3º nível)
- Mudar para item Maintenance (2º nível)
.
[HXCKQN1]
This field display your system's Service Tag.
If the Service Tag was not already set, you would be able to use this field to set it.
</syntaxhighlight>
- Mudar para item Asset Tag (3º nível)
- Nada fazer, mesmo estando sem valor
.
[_______]
This field allows you to create a system Asset Tag. The field can only be updated is the Asset
Tag is not already set.
</syntaxhighlight>
- Mudar para item SERR Messages (3º nível)
- Conferir marcação pois usaremos permitiremos essas mensagens
.
[v] Enable SERR Messages
This field controls the SERR message mechanism. Some graphics cards require that the
SERR message mechanism be disabled.
</syntaxhighlight>
- Mudar para item ImageServer (2º nível)
- Mudar para item Lookup Method (3º nível)
- Não alterar as marcações pois ImageServer não será usado neste servidor
.
( ) Static IP
(o) DNS
This field specifies how the ImageServer software will lookup server addresses.
DNS = ImageServer software will obtain server IP addresses using the Domain Name
System (DNS) protocol.
Static IP = ImageServer software will use static server IP addresses.
The factory default setting is DNS.
Note: This field is only relevant when the "Integrated NIC" control in the "System
Configuration" group is set to "Enable with ImageServer".
</syntaxhighlight>
- Mudar para item ImageServer IP (3º nível)
- Não alterar os valores pois ImageServer não será usado neste servidor
.
[255] [255] [255] [255]
This field specifies the primary static IP address of the ImageServer with the client
software communicates.
The factory default setting is 255.255.255.255.
Note: This field is only relevant when the "Integrated NIC" control in the "System
Configuration" group is set to "Enable with ImageServer" and when "Lookup Method" is set to
"Static IP".
</syntaxhighlight>
- Mudar para item ImageServer Port (3º nível)
- Não alterar os valores pois ImageServer não será usado neste servidor
.
[06910]
This field specifies the primary IP port of the ImageServer with the client software
communicates.
The factory default setting is 06910.
Note: This field is only relevant when the "Integrated NIC" control in the "System
Configuration" group is set to "Enable with ImageServer".
</syntaxhighlight>
- Mudar para item Client DHCP (3º nível)
- Não alterar os valores pois ImageServer não será usado neste servidor
.
( ) Static IP
(o) DHCP
This field specifies how the client will obtain the IP address.
DHCP = Client will obtain IP address using the Dynamic Host Configuration
Protocol (DHCP).
Static IP = Client will use static IP addresses.
The factory default setting is DHCP.
Note: This field is only relevant when the "Integrated NIC" control in the "System
Configuration" group is set to "Enable with ImageServer".
</syntaxhighlight>
- Mudar para item Client IP (3º nível)
- Não alterar os valores pois ImageServer não será usado neste servidor
.
[255] [255] [255] [255]
This field specifies the static IP address of the client.
The factory default setting is 255.255.255.255.
Note: This field is only relevant when the "Integrated NIC" control in the "System
Configuration" group is set to "Enable with ImageServer" and when "Client DHCP" is set to
"Static IP".
</syntaxhighlight>
- Mudar para item Client SubnetMask (3º nível)
- Não alterar os valores pois ImageServer não será usado neste servidor
.
[255] [255] [255] [255]
This field specifies the subnet mask of the client.
The factory default setting is 255.255.255.255.
Note: This field is only relevant when the "Integrated NIC" control in the "System
Configuration" group is set to "Enable with ImageServer" and when "Client DHCP" is set to
"Static IP".
</syntaxhighlight>
- Mudar para item Client Gateway (3º nível)
- Não alterar os valores pois ImageServer não será usado neste servidor
.
[255] [255] [255] [255]
This field specifies the gateway of the client.
The factory default setting is 255.255.255.255.
Note: This field is only relevant when the "Integrated NIC" control in the "System
Configuration" group is set to "Enable with ImageServer" and when "Client DHCP" is set to
"Static IP".
</syntaxhighlight>
- Mudar para item Licence Status (3º nível)
- Não alterar os valores pois ImageServer não será usado neste servidor
.
On-demand Desktop Streaming with EasyConnectTM Embedded Licence Status
No License
</syntaxhighlight>
- Mudar para item Post Behavior (2º nível)
- Mudar para item Fast Boot (3º nível)
- Conferir marcação pois usaremos este recurso
.
[v] Enable Fast Boot
This option can speed up the boot process by bypassing some compatibility steps.
</syntaxhighlight>
- Mudar para item Numlock LED (3º nível)
- Conferir marcação pois usaremos este recurso
.
[v] Enable Numlock LED
This option specifies whether the NumLock LED should be on when the system boots.
</syntaxhighlight>
- Mudar para item POST Hotkeys (3º nível)
- Conferir marcação pois usaremos este recurso
.
[v] Enable F12 = Boot Menu
These fields specifies whether the sign-on screen displays a message stating the keystroke
sequence required to enter the Setup program or the QuickBoot feature.
</syntaxhighlight>
- Mudar para item Keyboard Errors (3º nível)
- Conferir marcação pois não usaremos este recurso
.
[ ] Enable Keyboard Error Detection
This field specifies whether keyboard related errors are reported when the system boots.
</syntaxhighlight>
- Mudar para item MEBx Hotkey (3º nível)
- Conferir marcação pois usaremos este recurso
.
[v] Enable MEBx Hotkey
This field specifies whether the sign-on sreen display a message stating the keystroke
sequence required to enter the Manageability Engine BIOS Extensions (MEBx) Setup
program.
</syntaxhighlight>
- Mudar para item OS Install (3º nível)
- Conferir marcação pois não usaremos este recurso
.
[ ] OS Install
This field determines the maximum amount of system memory availeble to the operating
system. Some operating systems will not complete installation with more than 2 GB of
system memory. If enabled the maximum available memory is 256 MB.
</syntaxhighlight>
- Mudar para item System Logs (2º nível)
- Mudar para item BIOS Events (3º nível)
- Tela de monitoramento para quando sistema estiver em funcionamento
.
[Clear Log] [Mark All Entries]
DATE TIME TYPE DATA
------------------------------------------------------------------------
U 08/25/10 19:35:38 Log Area Cleared NONE
U 11/19/10 17:31:08 Out Of Range Chassis Intrusion
</syntaxhighlight>